|
01-11-2009, 03:52 PM | #1 |
Join Date: Mar 2005
Location: Maitland, NSW, Australia
|
Customising bows
OK. I need to put together a set of rules to enable a player to create a bow of any ST that he wants. I'm thinking along the lines of:
Pick a ST; look up a table to get cost, weight, damage and range; apply modifiers for length, material (wood, composite, steel), and quality. I know this has been discussed previously but I want to take previous suggestions and create a coherent set of rules. |
01-11-2009, 04:44 PM | #2 |
Join Date: Mar 2005
Location: Maitland, NSW, Australia
|
Re: Customising bows
Here is what I'm thinking. With this method there is no need for a table.
The base bow is 5' in length. Its MinST is equal to its ST rating; Damage: thr+1; Range: x15/x20; Weight: 2 lbs; Cost $100. For more variation, cost and weight could depend on the ST of the bow (e.g. cost might be $10 x ST) Modifiers. Material: A self bow made of good quality wood (e.g. elm) uses above stats. Fine quality wood (e.g. yew) increases ST by +1, and cost by 4x. MinST is unchanged. Composite construction increases ST by +2, and cost by 20x. MinST is unchanged. Length: Assuming weight is unchanged. Every +1 ft will decrease MinST by -1. Every -1 ft will increase MinST by +1. So a 3' bow will add +2 to MinST but everything else is unchanged. Weight: Increasing weight by 10% increases ST and MinST by +1, cost +10%. Decreasing weight by 10% will reduce ST and MinST by -1, cost -10% Quality: Fine quality craftsmanship will decrease MinST by -1, and cost 4x. Very Fine is -2 to MinST and cost is 20x. Cheap is +1 to MinST and cost is 40%. Improvised might be +2 MinST. If the wielder's ST is lower than the bow's MinST then the wielder's ST determines range and damage instead of the bow's ST. Apply a skill penalty of -1. ----------- So the Regular bow in Basic Set is 5' long, weighs 2 lbs, has ST 10, MinST 10, Range x15/x20, Damage thr+1 (1d-1). A halfling will need to reduce the length to around 3 feet. This will increase MinST to 12 but leave all other figures unchanged. If the Halfling has a lower ST then he needs to decrease the weight of the bow and/or pay for fine quality. A 6-foot English longbow has an increase in length by +1ft which reduces MinST by -1. It is also much heavier. Increasing weight by, say, +50% raises the weight to 3 lbs; increases ST to 15 and MinST to 14. Damage is thr+1 (1d+2). If the above longbow was made of yew (fine quality wood) then it has ST16. In this case damage wouldn't be affected since ST15 and ST16 both do 1d+2 but Range would increase. Last edited by DanHoward; 01-11-2009 at 09:59 PM. |
01-11-2009, 04:48 PM | #3 |
"Gimme 18 minutes . . ."
Join Date: Sep 2005
Location: Albuquerque, NM
|
Re: Customising bows
Should weight correlate to length?
Also, and I'm sorry if this is a stupid question, but I was watching the Last Samurai a few weeks back and the horsemen were using bows that were shorter on the bottom than the top, some sort of adaptation that allowed larger bows to be used on horseback. Is this historically accurate? How would it affect the game stats? Does it need to be modeled in your system, or is it merely a cosmetic feature? |
01-11-2009, 04:53 PM | #4 | ||
Join Date: Mar 2005
Location: Maitland, NSW, Australia
|
Re: Customising bows
Quote:
Quote:
Last edited by DanHoward; 01-11-2009 at 10:02 PM. |
||
01-11-2009, 05:06 PM | #5 |
Join Date: Mar 2005
Location: Maitland, NSW, Australia
|
Re: Customising bows
I think the same rule can be used for crossbows. Use the above to determine the stats for the bow. Then lay it horizontal and add a mechanism for firing it.
|
01-11-2009, 05:12 PM | #6 |
"Gimme 18 minutes . . ."
Join Date: Sep 2005
Location: Albuquerque, NM
|
Re: Customising bows
Did crossbows ever use metal "bows"? Is that covered under the "increased weight" category? Crossbows only have greater damage due to higher ST mechanical cocking systems, yes?
|
01-11-2009, 05:15 PM | #7 |
Join Date: Jan 2006
Location: Central Europe
|
Re: Customising bows
I like it!
One thought is that adding weight to a bow beyond the minimum needed for the length and draw weight is normally bad (because moving the arms back and forth wastes energy). It might be a good idea for ST to determine weight, rather than letting people vary both independently. The range for the English warbow looks too high. In my database of bow data, I only have two entries where range is over 20 x effective ST, and those were both fine composite bows firing flight arrows as a sport. Maybe letting some things increase both ST (which affects range) and range is too much? To match the Basic Set, I suggest that for humans a 6-7' bow have bulk -8, a 4-5' bow have bulk -7, and a 3' bow have bulk -6.
__________________
"It is easier to banish a habit of thought than a piece of knowledge." H. Beam Piper This forum got less aggravating when I started using the ignore feature |
|
|