11-15-2017, 11:39 AM | #1 |
Join Date: Jun 2008
Location: Cheltenham, PA
|
Ogre Miniatures Set 1 Assembly PDF?
Would SJG be willing to post a PDF of the assembly instructions for Set 1 now that it's shipping? I brought a Mk III to work today without them and only realized the secondaries had to match specific holes when I started assembly. It's not too hard to figure out from looking at a picture, but the instructions would have saved me a few minutes :)
Thanks!
__________________
Joshua Megerman, SJGames MIB #5273 - Ogre AI Testing Division |
11-15-2017, 12:20 PM | #2 |
Join Date: Oct 2014
Location: St. Louis, Missouri
|
Re: Ogre Miniatures Set 1 Assembly PDF?
I just glue the barrels in whatever hole I grab them for first. Mine will therefore have all manner of weird angles to them.
|
11-15-2017, 10:25 PM | #3 |
Join Date: Feb 2016
Location: Lancaster, PA
|
Re: Ogre Miniatures Set 1 Assembly PDF?
I don't know of a PDF, but the Minis Lite rules in the Set 1 box (at least the KS box, can't speak for retail) do have an assembly sheet as part of them. Worst case you can snapshot that with your phone or something.
__________________
Andy Mull MIB Agent #0460 Ogre 134th Battalion Lancaster, PA Imgur: https://agent0460.imgur.com/ |
11-15-2017, 10:33 PM | #4 |
Join Date: Oct 2014
Location: St. Louis, Missouri
|
Re: Ogre Miniatures Set 1 Assembly PDF?
The bare bones "instruction sheet" in the box doesn't use the part numbers though, it just shows the parts and where they go. So seemingly, the part numbers on the sprues are for show, and not really for reference.
|
11-16-2017, 07:54 AM | #5 | |
Join Date: Jun 2008
Location: Cheltenham, PA
|
Re: Ogre Miniatures Set 1 Assembly PDF?
Quote:
I only glanced at the sheet the night before, so I didn't remember that. That's disappointing, but easy enough to rectify when I have time - I'll just have to cut and fit them one at a time to match numbers to holes. And while I know I can just put them anywhere, I like to know what the instructions are before I ignore them... :P
__________________
Joshua Megerman, SJGames MIB #5273 - Ogre AI Testing Division |
|
11-17-2017, 08:27 PM | #6 |
Join Date: Jun 2010
|
Re: Ogre Miniatures Set 1 Assembly PDF?
An interesting request. Let me see what I can do.
That said, a lot of the staff are at either BGG.Con or PAX Unplugged. So this may take a little bit . . . D.
__________________
Proud sponsor of Ogre KS $4.5k Sheet #3 - Bringing the Vatican Guard, a Tiger-striped mercenary unit, and of course pink GEVs, to a game near you! Orders may be placed here. |
11-17-2017, 08:33 PM | #7 |
Join Date: Oct 2014
Location: St. Louis, Missouri
|
Re: Ogre Miniatures Set 1 Assembly PDF?
In assembling my Ogres, it seems like the secondary barrels should be placed as below (looking down on the Ogre, Ogre facing forward:
Front 2. 1. 4. 3. 6. 5. Rear |
11-18-2017, 04:31 PM | #8 | |
Join Date: Feb 2016
Location: Lancaster, PA
|
Re: Ogre Miniatures Set 1 Assembly PDF?
Quote:
Front 1 4 2 5 3 6 Rear Looks like it's firing randomly into a crowd, angled all over the place. Granted, I also assembled my first couple MSL tanks backwards, too...couldn't see the details well enough to realize that was the command center, so assumed sloped armor = forward. Oops.
__________________
Andy Mull MIB Agent #0460 Ogre 134th Battalion Lancaster, PA Imgur: https://agent0460.imgur.com/ |
|
11-18-2017, 04:51 PM | #9 |
Join Date: Oct 2014
Location: St. Louis, Missouri
|
Re: Ogre Miniatures Set 1 Assembly PDF?
I have to admit, the first batches of Ogres I built, I cut all the barrels off the runners, then glued them in place as I grabbed them. Those early Ogres have barrels wildly pointing to all sectors. The final four Ogres I built, I put them in the sockets as above, and they all look too sterile.
|
11-18-2017, 05:36 PM | #10 |
Join Date: Jun 2012
|
Re: Ogre Miniatures Set 1 Assembly PDF?
I am indecisive about parade ground order or battlefield animation.
|
Thread Tools | |
Display Modes | |
|
|