Steve Jackson Games - Site Navigation
Home General Info Follow Us Search Illuminator Store Forums What's New Other Games Ogre GURPS Munchkin Our Games: Home

Go Back   Steve Jackson Games Forums > Roleplaying > GURPS

Reply
 
Thread Tools Display Modes
Old 09-30-2013, 06:04 AM   #1
vicky_molokh
GURPS FAQ Keeper
 
vicky_molokh's Avatar
 
Join Date: Mar 2006
Location: Kyïv, Ukraine
Default [High-Tech] Drills: what's the point of the Armour Divisor?

Greetings, all!

PCs are considering drilling holes in a concrete ceiling to let through an endoscope. Looked up the DR and HP of 8" Reinforced Concrete at DR 96* and HP80, looked up power drill/hammer (the heavier one) damage at 2d+2(2). Okay, so what's the point of the (2)? It doesn't make a difference against steel thicker than about ¾" (unable to make a hole in it at all), and it has an absolutely negligible effect on the time it takes to drill anything made of concrete.

Thanks in advance!
__________________
Vicky 'Molokh', GURPS FAQ and uFAQ Keeper

Last edited by vicky_molokh; 04-15-2018 at 06:50 AM.
vicky_molokh is offline   Reply With Quote
Old 09-30-2013, 06:35 AM   #2
The Benj
 
Join Date: Aug 2004
Location: Platform Zero, Sydney, Australia
Default Re: [High-Tech] Drills: what's the point of the Armour Divisor?

Concrete drills are pretty specialised; I'm not sure how you'd do them in GURPS.
Otherwise, you're mostly relying on the ablative (or semi-ablative, I don't remember off the top of my head) nature of the DR. Which, like you said, means the divisor doesn't much matter (except to further diminish the minimum DR, I guess).
The Benj is offline   Reply With Quote
Old 09-30-2013, 06:37 AM   #3
gilbertocarlos
 
gilbertocarlos's Avatar
 
Join Date: Dec 2009
Location: Caxias do Sul, Brazil
Default Re: [High-Tech] Drills: what's the point of the Armour Divisor?

You can also drill wood, brick, etc...
Technically, the damage is the same as 5d pi-.
__________________
I've revised the Low Tech weapons table:
http://forums.sjgames.com/showthread.php?t=112532
gilbertocarlos is offline   Reply With Quote
Old 09-30-2013, 06:43 AM   #4
vicky_molokh
GURPS FAQ Keeper
 
vicky_molokh's Avatar
 
Join Date: Mar 2006
Location: Kyïv, Ukraine
Default Re: [High-Tech] Drills: what's the point of the Armour Divisor?

Quote:
Originally Posted by gilbertocarlos View Post
Technically, the damage is the same as 5d pi-.
No it isn't. That's my point. The armour divisor doesn't contribute to drilling wood/concrete, and is too low to allow gradually drilling a steel wall. It's unclear what purpose it serves.
__________________
Vicky 'Molokh', GURPS FAQ and uFAQ Keeper
vicky_molokh is offline   Reply With Quote
Old 09-30-2013, 09:56 AM   #5
Kromm
GURPS Line Editor
 
Kromm's Avatar
 
Join Date: Jul 2004
Location: Montréal, Québec
Default Re: [High-Tech] Drills: what's the point of the Armour Divisor?

You have DR 96, HP 80. Repeated huge piercing attacks (pi++) lower DR as if ablative (footnote, p. B559), to a minimum DR 3. Against a homogenous target like concrete, huge piercing has a wounding modifier of ×1/2 once it penetrates DR (p. B380).

With 2d+2 pi++, you'll average 9 points of damage per second. You'll need 10 seconds to ablate DR 90, leaving DR 6. On the 11th second, you'll put 3 points past DR 6, which will inflict 1 HP, and also ablate down to DR 3. Then you'll be putting 6 points per second past the minimum DR 3, inflicting 3 HP per second, for the next 26-27 seconds. Total time: 37-38 seconds.

With 2d+2(2) pi++, you'll average 9 points of damage per second. But now DR is halved! You'll need five seconds to ablate DR 45, leaving DR 3. Then you'll be putting 8 points per second past half the minimum DR 3, inflicting 4 HP per second, for the next 20 seconds. Total time: 25 seconds.

The main advantage is that if you're boring dozens of these a day on a worksite – say, to pass cable – you're taking 2/3 as long to do it. That's a huge savings in labor. When you're trying to be sneaky . . . well, a rotary hammer isn't the tool for the job! But 2/3 as long to be noticed should be good for reducing whatever bonus the GM gives your opponents for a sustained racket.
__________________
Sean "Dr. Kromm" Punch <kromm@sjgames.com>
GURPS Line Editor, Steve Jackson Games
My DreamWidth [Just GURPS News]
Kromm is offline   Reply With Quote
Old 09-30-2013, 10:05 AM   #6
vicky_molokh
GURPS FAQ Keeper
 
vicky_molokh's Avatar
 
Join Date: Mar 2006
Location: Kyïv, Ukraine
Default Re: [High-Tech] Drills: what's the point of the Armour Divisor?

Quote:
Originally Posted by Kromm View Post
You have DR 96, HP 80. Repeated huge piercing attacks (pi++) lower DR as if ablative (footnote, p. B559), to a minimum DR 3. Against a homogenous target like concrete, huge piercing has a wounding modifier of ×1/2 once it penetrates DR (p. B380).

With 2d+2 pi++, you'll average 9 points of damage per second. You'll need 10 seconds to ablate DR 90, leaving DR 6. On the 11th second, you'll put 3 points past DR 6, which will inflict 1 HP, and also ablate down to DR 3. Then you'll be putting 6 points per second past the minimum DR 3, inflicting 3 HP per second, for the next 26-27 seconds. Total time: 37-38 seconds.

With 2d+2(2) pi++, you'll average 9 points of damage per second. But now DR is halved! You'll need five seconds to ablate DR 45, leaving DR 3. Then you'll be putting 8 points per second past half the minimum DR 3, inflicting 4 HP per second, for the next 20 seconds. Total time: 25 seconds.

The main advantage is that if you're boring dozens of these a day on a worksite – say, to pass cable – you're taking 2/3 as long to do it. That's a huge savings in labor. When you're trying to be sneaky . . . well, a rotary hammer isn't the tool for the job! But 2/3 as long to be noticed should be good for reducing whatever bonus the GM gives your opponents for a sustained racket.
Wait, I don't get it:
2d+2(2) halves DR for purposes of penetration . . . but reading the entry on Semi-Ablative (B47) and DR loss on concrete (B559), it doesn't care about armour divisors, and is reduced based on damage rolled, not injury sustained.

Where does the faster ablation come from?
__________________
Vicky 'Molokh', GURPS FAQ and uFAQ Keeper
vicky_molokh is offline   Reply With Quote
Old 09-30-2013, 10:47 AM   #7
Kromm
GURPS Line Editor
 
Kromm's Avatar
 
Join Date: Jul 2004
Location: Montréal, Québec
Default Re: [High-Tech] Drills: what's the point of the Armour Divisor?

Quote:
Originally Posted by vicky_molokh View Post

2d+2(2) halves DR for purposes of penetration . . . but reading the entry on Semi-Ablative (B47) and DR loss on concrete (B559), it doesn't care about armour divisors
Where does either rule say, "ignore armor divisors"? Nowhere, because you don't do that. An attack with a divisor faces less DR in the first place. It's this DR that's reduced, not full DR. If I have a divisor (2), then I need to carve away DR 40 to get through a DR 80 ablative target. On the other hand, if another attack comes along, I've only carved away DR 40, so that attack still faces DR 40, because the DR just has a little hole in it.

Quote:
Originally Posted by vicky_molokh View Post

and is reduced based on damage rolled, not injury sustained.
Please check my examples again. Nowhere am I using injury. I only start applying the injury rules once the damage begins to penetrate DR. That's when homogenous kicks in.

Quote:
Originally Posted by vicky_molokh View Post

Where does the faster ablation come from?
The fact that pi++ is treated as ablative, not semi-ablative. The footnote on p. B559 is quite explicit on this point: "Repeated impaling, piercing, and large piercing . . . semi-ablative; repeated burning, corrosion, crushing, cutting, or huge piercing . . . ablative." And p. B47 is quite clear on how ablative DR works; namely, it's carved away on 1:1 basis by damage points. This is why just about all tools intended for slicing through bulk matter are either burning (burn) or huge piercing (pi++).
__________________
Sean "Dr. Kromm" Punch <kromm@sjgames.com>
GURPS Line Editor, Steve Jackson Games
My DreamWidth [Just GURPS News]
Kromm is offline   Reply With Quote
Old 09-30-2013, 10:53 AM   #8
Anthony
 
Join Date: Feb 2005
Location: Berkeley, CA
Default Re: [High-Tech] Drills: what's the point of the Armour Divisor?

Quote:
Originally Posted by Kromm View Post
Where does either rule say, "ignore armor divisors"?
Where does it say that armor divisors apply? There's no obvious reason they should, either realistically or from the game text. Also, from a game perspective, having armor divisors apply is a bad idea, it should be possible for attacks to have different performance for purposes of penetration vs damage to armor.
__________________
My GURPS site and Blog.

Last edited by Anthony; 09-30-2013 at 11:05 AM.
Anthony is offline   Reply With Quote
Old 09-30-2013, 11:27 AM   #9
Ulzgoroth
 
Join Date: Jul 2008
Default Re: [High-Tech] Drills: what's the point of the Armour Divisor?

Quote:
Originally Posted by Kromm View Post
Where does either rule say, "ignore armor divisors"? Nowhere, because you don't do that. An attack with a divisor faces less DR in the first place. It's this DR that's reduced, not full DR. If I have a divisor (2), then I need to carve away DR 40 to get through a DR 80 ablative target. On the other hand, if another attack comes along, I've only carved away DR 40, so that attack still faces DR 40, because the DR just has a little hole in it.
...So when you start drilling, the idea is that the (2) is supposed to tell you to divide the DR into two piles, one of which the attack ignores and the other of which the attack ablates?

I would never, ever have guessed that one.
__________________
I don't know any 3e, so there is no chance that I am talking about 3e rules by accident.
Ulzgoroth is offline   Reply With Quote
Old 09-30-2013, 11:28 AM   #10
Kromm
GURPS Line Editor
 
Kromm's Avatar
 
Join Date: Jul 2004
Location: Montréal, Québec
Default Re: [High-Tech] Drills: what's the point of the Armour Divisor?

Quote:
Originally Posted by Anthony View Post

Where does it say that armor divisors apply?
The general principle is that unless a rule is explicitly ruled out in a situation where it would apply (and I think a mechanic for DR depletion and a mechanic for DR reduction clearly apply to DR), it does apply. We don't explicitly say that cutting damage gets its ×1.5 injury vs. targets that aren't alive, but it does . . . we just leave it out of Injury to Unliving, Homogenous, and Diffuse Targets and assume that people will apply the multiplier because we didn't say not to. Most rules work like that in GURPS. The onus of proof is on those setting out to prove that rules don't apply, not those merely asserting that rules continue to apply.

Whether this is a good rule isn't what I'm discussing here. I'm explaining how the rules actually work.
__________________
Sean "Dr. Kromm" Punch <kromm@sjgames.com>
GURPS Line Editor, Steve Jackson Games
My DreamWidth [Just GURPS News]
Kromm is offline   Reply With Quote
Reply

Tags
drill, drilling, high-tech, structural damage

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Fnords are Off
[IMG] code is Off
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 12:49 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.